自掺杂SnO2微球的水热合成及其可见光催化性能

本研究采用水热法,以柠檬酸为螯合剂,通过控制n(Sn⁴⁺)/n(Sn²⁺)的数值,合成了由具有丰富氧空位的SnO₂纳米晶体组装成的微球。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶红外光谱(FT-IR)、X射线光电子能谱(XPS)及UV-Vis漫反射光谱对SnO₂纳米微球进行表征分析,结果表明:在酸性水热条件和柠檬酸的螯合作用下,二氧化锡纳米晶体聚集形成微球;在Sn⁴⁺/Sn²⁺摩尔比例为3:7时,其微球尺寸最小,整体分散性较好;同时适量二价锡离子的掺杂使得该样品氧空位浓度达到最佳,氧空位的存在将使得样品光吸收范围拓展至可见光,因而该样品显示出较强的可见光催化效率,在8 min内完全降解甲基橙。     

电机驱动微装配在双光子制备微结构中的应用

对微结构的制作、微装配系统进行了研究. 采用飞秒激光双光子聚合微加工技术制作有底座、精细的三维立体“拱形”微结构, 其高250μm、长300μm、厚50μm. 将此微结构与实验室自主搭建的二维微装配平台相结合, 利用自主编程的人机交互界面驱动步进电机, 远程操控微装配设备; 将荧光闪烁陶瓷粉末装配到微结构中, 对装配后的微结构进行荧光光谱表征发现, 纯荧光粉末和微结构中的荧光粉末的发射光谱在测量误差范围内基本一致, 表明荧光粉末的光学性质未发生改变. 利用该装置可以将各类微纳米级材料和微结构进行装配, 形成含有不同材料的微结构系统.     

CCSD(T) study on the structures and chemical bonds of AnO molecules (An = Bk–Lr)

The molecular geometries and dissociation energies of AnO (An = Bk–Lr) molecules were first obtained at thecoupled-cluster single-, double-, and perturbative triple-excitations [CCSD(T)] level of theory. Four hybrid functionals,B3LYP, M06-2X, TPSSh, and PBE0, were also employed in the calculations for the sake of comparison. In comparison ofthe CCSD(T) results, B3LYP, TPSSh, and PBE0 functionals can obtain more appropriate results than M06-2X and MP2.The analyses on molecular orbitals show that the 7s, 6d, and 5f atomic orbitals of actinide (An) atoms participate in thebonding of An–O bonds. The partial covalent nature between An and O atoms is revealed by QTAIM analyses.     

Asymmetric nonlinear-mode-conversion in an optical waveguide withPT symmetry

Asymmetric mode transformation in waveguide is of great significance for on-chip integrated devices with one-way effect, while it is challenging to achieve asymmetric nonlinear-mode-conversion (NMC) due to the limitations imposed by phase-matching. In this work, we theoretically proposed a new scheme for realizing asymmetric NMC by combining frequency-doubling process and periodic PT symmetric modulation in an optical waveguide. By engineering the one-way momentum from PT symmetric modulation, we have demonstrated the unidirectional conversion from pump to second harmonic with desired guided modes. Our findings offer new opportunities for manipulating nonlinear optical fields with PT symmetry, which could further boost more exploration on on-chip nonlinear devices assisted by non-Hermitian optics.     

射频等离子制备石墨烯负载Co3O4催化剂及其析氧性能研究

氢能的引入能有效提升配电网的供电可靠性,而电解水制氢是实现低碳转型的关键技术,开发高效的电解水催化剂势在必行。过渡金属氧化物储量大、催化活性高,是具有广阔应用前景的析氧反应催化剂。本文通过射频等离子体处理制备石墨烯上负载Co₃O₄析氧催化剂,XRD、Raman和XPS测试结果显示,二维结构石墨烯的引入加速表面电子迁移,增大了反应面积。等离子体处理促进了纳米粒子在石墨烯上的负载,利用等离子体刻蚀作用在催化剂表面制造出大量碳结构缺陷和氧空位结构,改善了活性位点分布,有效调控Co₃O₄电子结构,提高析氧催化活性。电化学测试表明,本文中合成的Co₃O₄@rGO在电流密度为50 mA·cm^-2时的过电位为410 mV,动力学反应速率较快,表现出优于商业IrO₂的析氧催化活性。     

吉林大学物理化学学科:笃学致远 润物无声

伴随建系而生的吉林大学物理化学学科是吉大化学学科的重要组成部分,在70年的发展中为整个化学学科的发展建设做出了重要贡献。吉大物化人一直坚持理论与实践并重的教育思想,培养了大批优秀人才。回顾了吉大物理化学学科的历史沿革,展现了吉林大学化学学院物理化学在课程和教材建设、科学研究和人才培养等方面所取得的成绩。在吉大化学70周年华诞之际,谨以此文向为吉大物化学科建设做出贡献的前辈致敬。     

QEPAS系统中石英音叉模态仿真计算与研究

对石英音叉增强型光声光谱(QEPAS)系统中常用的石英音叉进行了有限元模态计算，获得石英音叉前6阶振型与模态频率，认知了第4阶对称摆动振型为有效振动，利用单因素法分析了石英音叉的音臂长度l₁、音臂宽度w₁、音臂厚度t、音臂切角θ、音臂圆孔直径d及音臂圆孔高度h对低阶有效共振频率(Fre)的影响，敏感度依次为： l₁> w₁>d>θ>t>h，考虑实际设计情形，筛选出了l₁，w₁，d与h四个石英音叉设计变量，采用Box-Behnken实验设计方案与RSM(response surface methodology)方法，以Fre为函数目标，建立l₁，w₁，d与h的二次回归响应面模型，得到了参数之间的交互作用，利用Design-Expert软件对响应面模型进行设计参数反求，结果表明，在15 000 Hz≤Fre≤25 000 Hz计算区域内误差较小，基本满足QEPAS系统的计算需求，所提出的研究与设计方法具有一定通用性，可为QEPAS系统中石英音叉结构参数设计提供参考。     

Insight into shear‐induced modification for improving processability of polymers: Effect of shear rate on the evolution of entanglement state

Many experimental results have revealed that the re‐entanglement kinetics of disentangled polymers is much slower than that predicted by tube theory. This retarded recovery of fully entangled state is of practical significance that shear‐induced modification may offer a way to improve processability for a polymer by reducing viscosity. This work tried to figure out the shear‐rate dependence variation of viscosity in the view of evolution of entanglement state through disentanglement and re‐entanglement, aiming to provide fundamental insights into application prospect of shear‐induced modification in preparing “in‐pellet” disentangled polymers prior to final processing. High‐density polyethylene was sheared on a parallel‐plate rotational rheometer with a linearly increased shear rate. Results showed that higher shear rate could induce further disentanglement, resulting in a lower viscosity with a reduction rate up to 93.7%, larger molecular weight between entanglements M_e , and longer re‐entanglement time. Additionally, less entanglement would give a larger lamellar thickness of sheared samples after nonisothermal crystallization. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 598–606